Most newer power supplies don't provide -5 volts in which case the white wire is missing. Newer motherboards virtually never require -5 volts but many older motherboards do. The -5 volt line on pin 20 was made optional in ATX12V 1.3 (introduced in 2003) because -5 had been rarely used for years. These are pretty common on the 3.3 volt line in pin 13 but are sometimes used for other voltages too. Some of the voltage lines on the connector may have smaller sense wires which allow the power supply to sense what voltage is actually seen by the motherboard. The 24 pin connector is polarized so it can only be plugged in pointing in the correct direction. The extra pins made the auxiliary power cable unnecessary so most ATX12V 2.x power supplies don't have them. The new 24 pin connector added one line apiece for ground, 3.3, 5, and 12 volts. The older 20 pin main power cable only has one 12 volt line. The 24 pin main power connector was added in ATX12V 2.0 to provide extra power needed by PCI Express slots. Press OK, Press OK, and close windows.Standard 4.2mm Pitch ATX Header Connector Datasheet Display the printing status minimized in task bar.Ĩ.
![dell 725 printer cable dell 725 printer cable](http://www.freeprinterdriverdownload.org/wp-content/uploads/2014/08/Dell-V313w-printer-pix.png)
Select one of the following two options.ī. Click FILE on the top right corner and select Printing Preferences from the pull down menu.ħ. Select Printers & Faxes (or open the Control Panel and select the Printers & Faxes folder)Ĥ.
#DELL 725 PRINTER CABLE SOFTWARE#
If you ink level appears to be empty on the Printer Software please ignore this message & follow the instructions below to turn off or minimize the warning dialog box (please note, this works for the Dell M4640 & M4646 ink cartridges):Ģ. It is very common for Dell ink cartridges to incorrectly display ink levels. Gently wipe cartridge printhead and printer circuitry with a nonabrasive towel to ensure there is no debris. To fix this (1) Verify that tape is removed from the printhead. We recommend running routine maintenance on your printer to maintain peak performance and prevent debris buildup. To fix this refer to your printer user guide to run routine cleaning cycles. This is likely caused by paper fiber and/or debris buildup in the ink cartridge carriage. To fix this set the ink cartridge (printhead down) onto folded, moistened paper towel for 5 minutes, then reinsert into printer. This is likely caused by one one color bleeding into another. To fix this rest cartridge (printhead facing down) on paper towel and allow excess ink to balance. The likely cause of this is that the internal pressure is unbalanced. Reinstall and use printer cleaning cycle. Soak the printhead in warm water for 5 minutes. Avoid touching contacts with your fingers. Moisten a nonabrasive towel gently wipe printer contacts. Printer contacts may be worn or dirty OR your printhead may be partially clogged. Wrap the cartridge in an absorbent paper towel and shake lightly. Ensure tape covering printhead has been removed. Be sure tape has not been removed from printhead. For Remanufacutured Ink Cartridges Prints Only White Page (3) Power ON the printer and re-install the ink cartridge(s). (1) Remove the ink cartridge from the printer.
![dell 725 printer cable dell 725 printer cable](https://static.webcartridge.ie/images/product/regular/6805_usb-a-30---microusb-cable---18m_en.jpg)
(the plastic is generally yellow in color) Be sure that you have removed the plastic strip covering the cartridge vent holes. The ink cartridge is not being recognized
![dell 725 printer cable dell 725 printer cable](http://www.freeprinterdriverdownload.org/wp-content/uploads/2014/08/DellV505w-wireless-printer-pics.png)
If this does not work, please contact us. Run the head cleaning cycle 2 - 3 times. Print a test page to make sure the print cartridge(s) are installed and functioning properly. Run the head cleaning cycle at least one time. Be sure you've removed the plastic strip from the ink cartridge. The ink cartridge should be placed upright for at least 30 minutes prior to use this will allow the ink to flow down to the print head and allow any oxygen bubbles to rise up and away from the print head. Your ink cartridges will last longer if you do not remove your cartridge from the protective wrapping until it's ready for use. If these don't help, please contact us - we're happy to assist in solving any and all printer problems.įor Compatible Ink Cartridges Installing your print cartridge properly Printer Cartridge Problems? Below are some common printer cartridge problems and our recommendations for resolving the issues.